DIS nie wykrywa pojazdu na przejściówce na 20 pin

**Kosiara** · 19 Lutego 2012

Witam.

Postanowiłem założyć nowy post ponieważ nie mogłem znaleźć :reading: nigdzie odpowiedzi na moje pytanie związane z wykrywaniem pojazdu w programie DIS oraz Impie jest brak zapłonu.Posiadam interfejs na USB OBD II i przejściówkę na 20 pin. Po wejściu do impy na głównym oknie battery: ON a Ignition: OFF na prze kręconym zapłonie później wybieram silnik i sprawdzam błędy i odczyt parametrów i wszystko działa w programie DIS mam tak ze muszę wybierać manualnie samochód bo pisze mi ze jest nie włączony zapłon po wybraniu manualnie samochodu wszystko działa i sprawdza błędy. Problemy pojawiają się tylko jak mam przejściówkę na złącze 20 pin a jak podłączam samochody do OBD II wszystko jest ok i nie ma problemu z wykrywaniem auta w dis. Proszę o poradę w załączniku na zdjęciach jest mój interfejs oraz przejściówka z opisanymi przewodami który gdzie idzie, dodatkowo wklejam plik EDIBASE. :modlitwa:

Poniżej mój schemat jak są podłączone piny z OBD II do BMW(20Pin):

USB- OBD II>>>>>>>>BMW(20Pin)

4,5>>>>>>>>>>>19(Ground)Czarny

7,8>>>>>>>>>>>17,20(K Line) Brązowy

15>>>>>>>>>>>15(L Line) Żółty

16>>>>>>>>>>>16(Power) Zielony

12>>>>>>>>>>>7 Pomarańczowy :think:

http://www.electronicsss.neostrada.pl/Pompa/8.JPG

http://www.electronicsss.neostrada.pl/Pompa/9.JPG

http://www.electronicsss.neostrada.pl/Pompa/10.JPG

http://www.electronicsss.neostrada.pl/Pompa/11.JPG

http://www.electronicsss.neostrada.pl/Pompa/12.JPG

http://www.electronicsss.neostrada.pl/Pompa/16.JPG

Dodatkowo wyskakuje mi takie coś jak włączam impe:

http://www.electronicsss.neostrada.pl/Pompa/15.JPG

Plik EDIABAS.ini z folderu Ediabas\bin

;=============================================================================

;EDIABAS 6.4.3 Configuration

[Configuration]

;=============================================================================

;-----------------------------------------------------------------------------

; EcuPath

; Description : ECU file path

; Default = .

EcuPath = C:\EDIABAS\ECU

;-----------------------------------------------------------------------------

; SimulationPath

; Description : Simulation file path

; Default = .

SimulationPath = C:\EDIABAS\SIM

;-----------------------------------------------------------------------------

; TracePath

; Description : Trace file path

; Default = .

TracePath = C:\EDIABAS\TRACE

;-----------------------------------------------------------------------------

; CodeMapping

; Description : Character mapping file path

; Default = .

;CodeMapping = C:\EDIABAS\BIN\ansi2oem.tab

;-----------------------------------------------------------------------------

; TraceSize

; Description : Maximum size of each trace file [KB]

; Value : 0..32767

; Default = 1024

;TraceSize = 1024

;-----------------------------------------------------------------------------

; ApiTrace

; Description : Enable/Disable API/User trace

; Value : 0 = Trace disabled

; 1 = User trace

; 2 = User trace + time stamp

; 3 = User trace + time stamp + process id (Win32)

; 4 = Function trace

; 5 = Function trace + time stamp

; 6 = Function trace + time stamp + timing

; 7 = Function trace + time stamp + timing + process id (Win32)

; Default = 0

ApiTrace = 0

;-----------------------------------------------------------------------------

; IfhTrace

; Description : Enable/Disable IFH trace

; Value : 0 = Trace disabled

; 1 = Trace enabled

; 2 = Trace enabled

; 3 = Trace enabled

; Default = 0

IfhTrace = 0

;-----------------------------------------------------------------------------

; SystemTraceSys

; Description : Enable/Disable system trace (runtime system)

; Value : 0 = Trace disabled

; Trace levels 1..7

; Default = 0

SystemTraceSys = 0

;-----------------------------------------------------------------------------

; SystemTraceBip

; Description : Enable/Disable BIP trace (runtime system)

; Value : 0 = Trace disabled

; Trace levels 1..7

; Default = 0

SystemTraceBip = 0

;-----------------------------------------------------------------------------

; SystemTraceIfh

; Description : Enable/Disable IFH system trace

; Value : 0 = Trace disabled

; Trace levels 1..7

; Default = 0

SystemTraceIfh = 0

;-----------------------------------------------------------------------------

; SystemTraceNet

; Description : Enable/Disable network trace

; Value : 0 = Trace disabled

; Trace levels 1..7

; Default = 0

SystemTraceNet = 0

;-----------------------------------------------------------------------------

; BipDebugLevel

; Description : BIP debug level of ECU files

; Value : 0..32767

; Default = 0

BipDebugLevel = 0

;-----------------------------------------------------------------------------

; UbattHandling

; Description : Ubatt ON/OFF handling

; Value : 0 = Ubatt ON/OFF: No EDIABAS error

; 1 = Ubatt ON/OFF: EDIABAS error

; Default = 1

UbattHandling = 0

;-----------------------------------------------------------------------------

; IgnitionHandling

; Description : Ignition ON/OFF handling

; Value : 0 = Ignition ON/OFF: No EDIABAS error

; 1 = Ignition ON/OFF: EDIABAS error

; Default = 1

IgnitionHandling = 0

;-----------------------------------------------------------------------------

; TaskPriority

; Description : EDIABAS process/thread priority (only Win32/16)

; Value : 0 = Optimal EDIABAS performance = 8

; 1 = Minimal EDIABAS performance

; ..

; 10 = Maximal EDIABAS performance

; Default = 0

TaskPriority = 0

;-----------------------------------------------------------------------------

; LoadWin32

; Description : Map EDIABAS Win16 calls to EDIABAS Win32

; Value : 0 = Win16/32 Mapping disabled (Win16-->Win16)

; 1 = Win16/32 Mapping enabled (Win16-->Win32)

; Default = 0 for Windows 9x/Me

; Default = 1 for Windows NT4/2000/XP

;LoadWin32 = 0

;-----------------------------------------------------------------------------

; SystemResults

; Description : Enable/Disable system results (ubatt/ignition/jobstatus)

; Value : 0 = Disable system results

; 1 = Enable system results

; Default = 1

SystemResults = 1

;-----------------------------------------------------------------------------

; RetryComm

; Description : Repeat failed communication automatically (1x)

; Value : 0 = Retry disabled

; 1 = Retry enabled (1x)

; Default = 1

RetryComm = 1

;-----------------------------------------------------------------------------

; Simulation

; Description : Enable/Disable ECU simulation

; Value : 0 = Simulation disabled

; 1 = Simulation enabled

; Default = 0

Simulation = 0

;-----------------------------------------------------------------------------

; Interface

; Description : Connected diagnosis interface

; Default = EDIC

Interface =STD:OBD

; Additional information (in German) :

; Bitte beachten: Der HW-Treiber fuer das Interface muss installiert sein!

; Interface = STD:OBD

; Beschreibung : Serieller Pegelwandler (Nachfolger von ADS / Anschluss an OBD-Dose)

; Installation : \EDIABAS\HARDWARE\OBD\ODBSETUP (nur noetig fuer WIN NT4, WIN 2000, WIN XP)

; INI-Datei : OBD.ini nur benutzt wenn im Windows-Verzeichnis

; Unterstuetzung : WIN3.xx : Nein

; WIN95,98 16-Bit : Ja

; WIN95,98 32-Bit : Ja

; WIN NT 4.0 : Ja

; WIN XP : Ja

; Interface = STD:FUNK

; Beschreibung : Funk-Diagnose Interface MDA von Fa. Siemens

; Installation : keine

; INI-Datei : FUNK.INI

; Unterstuetzung : WIN95,98 16-Bit : Ja

; WIN95,98 32-Bit : Ja

; WIN NT 4.0 : Ja

; WIN XP : Ja

; Interface = ADS

; Beschreibung : Serieller Pegelwandler (Anschluss an Diagnose-Dose)

; Installation : \EDIABAS\HARDWARE\ADS\ADS32\ADSSETUP (nur fuer WinNT4 noetig)

; INI-Datei : keine

; Unterstuetzung : WIN95,98 16-Bit : Ja

; WIN95,98 32-Bit : Nein

; WIN NT 4.0 : Ja

; WIN XP : Ja

; Interface = KBUS

; Beschreibung : Serieller Pegelwandler (Anschluss direkt an K-Bus oder I-Bus)

; Installation : \EDIABAS\HARDWARE\ADS\ADS32\ADSSETUP (nur fuer WinNT4 noetig)

; INI-Datei : keine

; Unterstuetzung : WIN95,98 16-Bit : Ja

; WIN95,98 32-Bit : Nein

; WIN NT 4.0 : Ja

; WIN XP : Ja

; Interface = EDIC

; Beschreibung : Serielles , PCMCIA , PC-Card Interface von Fa. Softing

; Installation : \EDIABAS\HARDWARE\EDIC\SETUP.EXE

; INI-Datei : EDICFW.INI, EDICHW.INI

; Unterstuetzung : WIN95,98 16-Bit : Ja

; WIN95,98 32-Bit : Ja

; WIN NT 4.0 : Ja

; WIN XP : Ja

; Interface = EDICC

; Beschreibung : EDIC-Card C oder EDIC-Card 2 CAN-Interface von Fa. Softing

; Installation : \EDIABAS\HARDWARE\EDIC\SETUP.EXE

; INI-Datei : XEDICC.INI

; Unterstuetzung : WIN95,98 16-Bit : Ja

; WIN95,98 32-Bit : Ja

; WIN NT 4.0 : Ja

; WIN XP : Ja

; Interface = STD:CAN

; Beschreibung : PCMCIA CAN-Interface CanCardX von Fa. Vector

; Installation : keine (ausser Installation der CAN-Karte)

; INI-Datei : CANRTTP.INI

; Unterstuetzung : WIN95,98 16-Bit : ?

; WIN95,98 32-Bit : ?

; WIN NT 4.0 : Ja

; WIN XP : ?

; Ansprechpartner: Hr. Jusko

; Telefon : +49-(0)89/382-35891 (Hotline)

; email : [email protected] (Hotline)

; Interface = STD:ADS4MOST

; Beschreibung : Most-Interfaces von Fa. Oasis

; Installation : keine (ausser Installation der Oasis-Karte)

; INI-Datei : ADS4MOST.INI

; Unterstuetzung : WIN95,98 16-Bit : ?

; WIN95,98 32-Bit : ?

; WIN NT 4.0 : Ja

; WIN XP : Ja

; Ansprechpart.: Hr. Rowedder

; Telefon : 089 / 382-29159

; email : [email protected]

; Interface = REMOTE

; Beschreibung : Anbindung eines EDIABAS-Interfaces über TCP/IP

; Installation : Anpassung der Einträge in [TCP] auf beiden Seiten (ins.: RemoteHost, Port)

; INI-Datei : keine

; Unterstuetzung : WIN95,98 16-Bit : Nein

; WIN95,98 32-Bit : Ja

; WIN NT 4.0, XP : Ja

; WIN XP : Ja

; Sonderfall : Interface OPPS

; Ansprechpart.: Hr. Rowedder

; Telefon : 089 / 382-29159

; email : [email protected]

; Interface = REMOTE:name

; Beschreibung : Anbindung eines EDIABAS-Interfaces über TCP/IP

; Installation : Anpassung der Einträge in [TCP] auf beiden Seiten (ins.: RemoteHost, Port)

; INI-Datei : REMOTE.INI (insbesondere für Parallelbetrieb notwendig)

; In REMOTE.INI stehen unter [name] spezif. Einstellungen(z.B.: RemoteHost, Port)

; Unterstuetzung : WIN95,98 16-Bit : Nein

; WIN95,98 32-Bit : Ja

; WIN NT 4.0, XP : Ja

; WIN XP : Ja

; Sonderfall : Interface OPPS

; Ansprechpart.: Hr. Rowedder

; Telefon : 089 / 382-29159

; email : [email protected]

;-----------------------------------------------------------------------------

; NetworkProtocol

; Description : Network protocol

; Default =

NetworkProtocol = TCP

;=============================================================================

;TCP/IP Configuration

[TCP]

;=============================================================================

;-----------------------------------------------------------------------------

; RemoteHost

; Description : server address/name

; Default =

RemoteHost = 192.168.100.30

;-----------------------------------------------------------------------------

; Port

; Description : IP communication port

; Value : 1000 < port < 30000

; Default =

Port = 6801

;-----------------------------------------------------------------------------

;TimeoutConnect

; Description : Timeout for establishing the connection

; Default = 5000

TimeoutConnect = 2000

;-----------------------------------------------------------------------------

;TimeoutReceive

; Description : Timeout for receiving a message

; Default = 5000

TimeoutReceive = 2000

;-----------------------------------------------------------------------------

;TimeoutFunction

; Description : Timeout for a long function

; Default = 59000

TimeoutFunction = 10000

;-----------------------------------------------------------------------------

;DisconnectOnApiEnd

; Description : Enable/Disable Disconnection with function call ApiEnd

; Value : 0 = Disconnection disabled

; 1 = Disconnection enabled

; Default = 0

;DisconnectOnApiEnd = 1

;-----------------------------------------------------------------------------

;InitCmd

; Description : Initialization command (normally for OPPS)

; Default =

;InitCmd0 = FE,04,00,03,01

;InitCmd1 = FD,05,00,03,01

;=============================================================================

; End Of File EDIABAS.ini

;=============================================================================

Plik obd.ini z folderu Ediabas\bin

[OBD]

Port=Com1

TRACELEVEL = 0x00000000

HARDWARE=OBD

RETRY=ON

MODE=NORMAL

;OBD-Stecker OBD

;OBD-Stecker am USB->Seriell-Adapter USB

;alte ADS-Hardware ADS

;Tracelevel=0xFFFFFFFF

;Tracelevel=0xF0000000

;Tracelevel=0x0000FFFF

; Bit 0 = Funktionsaufruf

; Bit 1 = io Ergebnis

; Bit 2 = nio Ergebnis

; Bit 3 = Detailinfos

; Nibble 0 = readchar_wait

; Nibble 1 = main

; Nibble 2 = cmd

; Nibble 3 = obd

; Nibble 4 = send_and_receive_...

; Nibble 5 = read_telegram_...

; Nibble 6 = send_telegram

; Nibble 7 = SendData

;[uNIT_x] x = A, B, ...,Y, Z, 0, 1, .., 8, 9

;Port = Com1 COM1 .. COM9

;TRACELEVEL = 0x00000000 0x00000000 .. 0xFFFFFFFF

;RETRY = OFF OFF, ON

;MODE=NORMAL NORMAL, KBUS

;HARDWARE=OBD OBD, USB, ADS

[uNIT_A]

Port=Com1

TRACELEVEL = 0x00000000

Hardware=OBD

RETRY=ON

MODE=NORMAL

[uNIT_B]

Port=Com2

Hardware=OBD

[uNIT_C]

Port=Com3

Hardware=OBD

[uNIT_D]

Port=Com4

Hardware=OBD

[uNIT_E]

Port=Com5

Hardware=OBD

[uNIT_F]

Port=Com6

Hardware=OBD

[uNIT_G]

Port=Com7

Hardware=OBD

[uNIT_H]

Port=Com8

Hardware=OBD

[uNIT_I]

Port=Com9

Hardware=OBD

[uNIT_J]

Port=Com10

Hardware=OBD

[uNIT_K]

Port=Com11

Hardware=OBD

[uNIT_L]

Port=Com12

Hardware=OBD

[uNIT_M]

Port=Com13

Hardware=OBD

[uNIT_N]

Port=Com14

Hardware=OBD

[uNIT_O]

Port=Com15

Hardware=OBD

Bardzo będę wdzięczny za pomoc w rozwiązaniu problemu. :cool2:

**Kosiara** · 20 Lutego 2012

???

**Kosiara** · 20 Lutego 2012

No własnie opisałem wszystko w pierwszym poscie ale nie wiem jak rozwiazac problem.

**chanky** · 22 Lutego 2012

Sorry, ale jak juz pisze w okienku prosze czytac. Trzeba dodac Parametry do registry :-)

Start -> wykonac -> regedit -> ok <- nie wiem czy u ciebei bedzie tak.

Tu masz parametry

http://img843.imageshack.us/img843/9206/registry.png

Uploaded with ImageShack.us

Powodzenia

**stanek90** · 3 Marca 2012

Trzeba zmoskowac w fejsice piny.np zwykłym przeowdem cienkim 1 z 16 w przypadku takiej przejsciowki

OBD-2 BMW 16Pin <<<< === >>>>> OBD- BMW 20Pin

1 --------------------------------------------------16 ( Zündung /

Zapłon +12V )

4 / 5 ----------------------------------------------19 ( GND )

7 / 8 ----------------------------------------------17/20 ( K-Line )

15 -------------------------------------------------15 ( L- Line )

16 -------------------------------------------------14 ( +12V / Bat.)

**Kosiara** · 3 Marca 2012

Tak mam zrobione własnie.

**lapidem** · 6 Marca 2012

Miałem podobny błąd

Pomaga przestawienie opcji w DIS

"Zaleca sie uzywanie do aut z okragla 20 pinowa wtyka trybu FISTER i ustawienia VM na off."

Zaloguj się

DIS nie wykrywa pojazdu na przejściówce na 20 pin

Rekomendowane odpowiedzi

Kosiara

Kosiara

Kosiara

chanky

stanek90

Kosiara

lapidem

Jeśli chcesz dodać odpowiedź, zaloguj się

Ostatnio przeglądający 0 użytkowników

Przeglądaj

Cała aktywność

Powiadomienie o plikach cookie